OBSBOT Tail 2 Kit for Elgato Prompter
Use your OBSBOT Tail 2 with the Elgato Prompter. The custom adapter for the Tail 2 includes flexible cable management slot on both sides so your cables are kept nice and tidy. This kit includes:
Part A - x1 OBSBOT Tail 2 Prompter Bracket
Part B - x1 Low Profile Thumboney Screws
Part C - x1 Medium Thumboney Screw
IMPORTANT NOTES:Â
- This bracket is best used with the Elgato universal plate that has the light blocking cloth attach to it (see images at end of gallery). Since the OBSBOT Tail 2 is a PTZ with a moving lens and doesn't stay mounted to the Elgato Prompter, it's best to drape the cloth over the entire OBSBOT camera to block any light from entering the prompter. If you choose to use the Elgato lens mount plate, the lens will still be centered but you may get light bleed into your camera footage.
- THIS BRACKET DOES NOT FIT THE PROMPTER XL. Regular prompter only.
OBSBOT Tail Air Kit for Elgato Prompter
Use your OBSBOT Tail Air with the Elgato Prompter. The custom bracket for the Tail Air includes a slot of your cables to fit into and keep nice and tidy.Â
This kit includes:
- Part A - x1 OBSBOT Tail Air Prompter Bracket
- Part B - x2 Low Profile Thumboney Screws
How does it work? View the setup guide.Â
Does this support Tiny2 or Tiny2 4k? Technicall, yes. You can flip this bracket upside down and the Tiny2's could sit right on top. It might not be perfectly center in the prompter, but it could work although I did not test this for extended periods of time, and the included Elgato bracket should really work just fine for this anyways.Â
IMPORTANT NOTE:Â This bracket is best used with the Elgato universal plate that has the light blocking cloth attach to it. Since the OBSBOT Tail Air is a PTZ with a moving lens and doesn't stay mounted to the Elgato Prompter, it's best to drape the cloth over the entire OBSBOT camera to block any light from entering the prompter.Â
VESA 100mm to 1/4"-20 Adapter (2-screw)
Using this adapter, connect your portable monitor that uses x2 hole 100mm VESA mount to any 1/4"-20 friction arm for easy mounting. This version is meant for portable monitors that have x2 100mm VESA screw holes. I also make a 4 screw version for monitors like the UPERFECT portable monitors that have 75mm holes. PLEASE VERIFY IF YOUR MONITOR HAS 75mm OR 100mm VESA BEFORE ORDERING AS ITEMS ARE MADE TO ORDER AND NON-REFUNDABLE.
THREE OPTIONS
- Standard: 1/4-20 and VESA holes are both centered
- Offset: If your monitor VESA holes are close to the lip/edge
- Cable Clip: Built in clips for cable management, slots for cable/zip ties
(All three options will work with any x2 hole 100mm vesa monitor. It's purely an aesthetic choice)
Video on how they work: https://youtu.be/Xuy1Fi_Bef8?si=m2AurfSawliAb4U3
KEY FEATURES
- Converts VESA 100mm to 1/4"-20 for use with mounting hardware
- Compatible with 1/4"-20 mounts that use safety pins for anti-rotation (like the smallrig rosette)
- 3D Printed using black glass-fiber PETG, strong and beautiful
INCLUDED IN THIS KIT
- [x1] 100mm to 1/4"-20 adapter
- [x1] 1/4"-20 brass threaded insert (installed in adapter)
- [x2] m4 x 8mm thumbscrews (with Phillips head compatibility)
IMPORTANT NOTICES ABOUT PRODUCT
(1) While the PETG-Glass Fiber filament is both flexible and strong, with enough force they can snap. They are NOT designed to flex a lot, but moreso to be a solid foundation for cables to be secured to.Â
(2) The VESA adapters are for portable monitors ONLY. Portable monitors typically weigh between 1-3lbs. While these adapters could* be used with larger monitors as they have the same 100mm layout, they are not designed to hold all of the extra weight. If you have an iPad with a vesa mount, just check to make sure the weight is not over 8lbs and test the part with the mount before permanently mounting.
(3) All parts are 3D printed using Glass Fiber PETG filament.
(4) NackHabitat does their part to save the planet. Shipping materials are made from recyclable materials and some are even made in house. a) Some products are shipped using cardboard that was previously used for shipping. This cardboard may have markings, scuffs, bends, logos, etc. b) Cardboard and paper is cut with a laser that may produce a small amount of dust or paper bits. c) Parts are wrapped using recyclable honeycomb paper that can leave a small amount of residue on part. Wipe any dust residue that may have collected from recyclable shipping materials and you're good to go, none of it is permanent.
(5) SmallRig friction arm or colored anodized thumbscrews shown in photos are not included. As of Jan. 22nd 2026 all colored thumbscrews were removed and replaced with black or white thumbscrews that have Phillips (+) head compatibility.
VESA 75mm to 1/4"-20 Adapter (4-screw)
Do you wish you could find a way to easily mount your portable monitor that uses 100mm or 75mm VESA mount, but only have a friction arm? Got you covered. These adapters let you take any friction arm that uses a 1/4"-20 thread for mounting and connect it to your portable monitor.Â
Key Features
- Converts VESA 75mm to 1/4"-20 for mounting
- Compatible with 1/4"-20 mounts that use safety pins for anti-rotation
- 3D Printed using black glass-fiber PETG, strong and beautiful
- High Quality brass 1/4"-20 threaded insert·x4 #6-32 aluminum screws
Included in this kit
- [x1] 3D Printed 75mm to 1/4"-20 adapter
- [x1] 1/4"-20 brass threaded insert (installed in adapter)
- [x4] m4 screws (will be black or white thumbscrews)
IMPORTANT NOTICES ABOUT PRODUCT
- These adapters are designed to be used with portable monitors weighting in around 5-8lbs and are not designed for full size, desktop monitors.
- To reduce the use of plastic shipping materials, parts are wrapped in a paper honeycomb packing paper which may leave a dusty residue on the part itself. Simply wipe the part to remove any dust or residue as this is not permanent. Save the planet!
- All products are made to order!
- SmallRig friction arm NOT INCLUDED.
VESA 75mm to 1/4"-20 Adapter (2-screw)
Mount your portable monitor to any 1/4" mounting system, like the very common friction arm that uses a 1/4"-20 thread for mounting photo or video equipment. This version is meant for portable monitors that have x2 VESA screw holes. (I also make a 4 screw version)
There are a lot of portable monitors out there, and they all are slightly different sizes and shapes with different locations of VESA holes. If you have a UPERFECT monitor where the screw holes are close to the edge and don't want the adapter hanging off the edge, I recommend the skinny or offset version. If you have 2 VESA screw holes that have plenty of space around them and you want the most surface area covered as possible, go for the chunky version.
Key Features
- NEW v2 now featuring a built-in cable clip with velcro & zip tie pass-through for securing cables
- Converts VESA 75mm to 1/4"-20 for mounting
- Compatible with 1/4"-20 mounts that use safety pins for anti-rotation
- 3D printed using black glass-fiber PETG, strong and durable
- High-quality brass 1/4"-20 threaded insert
- x4 #6-32 aluminum screws
- Custom-designed aluminum screws with 3D printed head
Choose Your Kit
- Choose v1 (no cable clip) or v2 (with cable clip)
- Choose Standard, Skinny, or Offset screw hole placement (see images for explanation)
Included in This Kit
- [x1] 3D printed 75mm to 1/4"-20 adapter (2 screw version)
- [x1] 1/4"-20 brass threaded insert (installed in adapter)
- [x2] M4 x 8mm thumbscrews (with flat head compatibility)
Important Notices About Product
- These adapters are designed for portable monitors weighing approximately 5–8 lbs and are not intended for full-size desktop monitors. The parts are printed in glass fiber PETG with an orientation that improves strength, but they are intended for lightweight use only.
- To reduce plastic waste, parts are wrapped in recyclable honeycomb paper, which may leave a light dust residue. Simply wipe clean; this is not permanent.
- All products are made to order.
- SmallRig friction arm not included.